Replaced my old foam even though I didn't feel it was all that worn out. Best move I could've made. After replacing the foam and putting on the new covers I felt like I was back in a new truck again. Don't waste your time replacing the bottom cover without this as well!

If your seat foam is disintegrated on the left side from climbing in and out this will be a welcome repair to get you sitting upright again. The seat firmness is noticeably firmer than the old OEM one and I actually feel like I sit higher and see better. The sides of the seat now cup your butt firmly and give a sense of control as you drive. The dimensions are made exactly so it fit perfectly in the seat frame and the seat cover fit over it without any sagging or wrinkles. The installation was fairly simple. Overall, I'm glad I purchased this one over a cheaper knock-off because it fit correctly and will give better comfort over a long trip.

I purchased both the upper and lower heating elements not knowing which if any was actually bad. Turned out the upper one was fried and this fixed the issue. It uses a sticky strip to secure to the foam at the top and the bottom, although I did have issues with it sticking correctly. It might've been better to use upholstery adhesive instead like the old ones did, but this was a bit more convenient initially. Returning the unused one was simple and highly recommended if you're not sure which one you need and you're replacing both covers. The only thing I'm out is the cost of return shipping which was cheap insurance to be sure I had the correct parts on hand during my install of the new covers.

My 2001 Chevy Silverado seat was breaking down. I did not realize how uncomfortable it was until I installed this new seat. I had help as I could not lift the seat by myself. It took us a few hours but that's because we wanted it to be perfect, and it is. I drove my truck 6 hours immediately after the installation on a trip and my butt was so happy. Can't tell you how great this seat feels and how I'm kicking myself for not doing this sooner. I actually bragged to my Farrier (whose seat is wrecked) how great it was, showed him and then sent him your link. Thanks.

Was a direct match to my OEM color and replacement seat cushion . Cant go wrong with these people. Very courteous customer support on helping me getting the right cover ordered. Highly recommended company.

perfect replacement and very easy to install with new bottom cover.

I'm so glad I bought the new foam to go with my new leather cover. Fit perfectly and really made me realize how out of shape my old foam had gotten. My old seat is new again.

I ordered this seat cushion and had it installed the other day. I had 200,000 miles on the old one. This one is real nice. Even the people at the shop who did the install were impressed. The ride home after the install was great. The people at "The Seat Shop" were real nice and extremely helpful when I called them to discuss the product. This all worked out great and I'm completely satisfied.

Received the foam and was surprised at the weight and density of the foam which should add to comfort and durability. I have the LTZ package with heated seat. It would be useful if the seat came with additional adhesive strips to reattach the heating pad to it. I'm hoping the snugness of the seat cover along with center clips holding the cover in place keeps the pad from moving between the foam and seat cover. After installing, I immediately felt the difference! I hope it least as well as the OEM...10 years.

Precise fit for 2004 FORD EXPEDITION EDDIE BAUER with AC / Heated seats. Just make sure you request for AC / Heated seats if you have them.

Great fit and relatively easy install after watching the video a couple times (highly recommended) https://youtu.be/aEU3eUA8QIs I installed in my 2011 Chevy Tahoe LTZ in about 2hrs. A few notes that might be helpful: 1. As noted in the video, you will need 15mm and 11mm sockets -- deep well sockets will likely be necessary. You can pick these up at HomeDepot for a few bucks each. 2. My seatbelt anchor was *not* a T50. It came off with the 15mm socket. 3. I have after-market heated seats. There were a couple additional disconnect to be made under the seat. No more difficult that the two OEM disconnects. 4. The heating element had previously been glued to the foam with a spray adhesive. It peeled off easily without any damage. I tried to secure the heating element to the new cushion with some double-sided carpet tape. The tape did not stick to the foam very well. I secured it with some spray adhesive from the kids crafting supplies.

My original seat after 205,000 miles and 18 years had enough. The worst part was the sagging from left to right, which had caused some back pain. The seat with the new cushion installed is glorious, and took up almost 2 inches of sag. Also, surprisingly the old seat had gotten bouncy enough to accentuate body roll and bumpy roads. With the new seat it almost feels like a new set of shocks on the truck. The only thing in the way of a full 5 stars is the hog-ring setup to get the seat cover onto the cushion. The bars in the cushion were a little deeper set than the OE piece, and made using the hog rings that much more of a pain in the neck.

I'm so happy I purchased this cover. Makes my seat look brand new again. Matches the factory color, great quality. I'm super happy with it!

After watching the install video a couple of times, I ordered the replacement cover. It arrived in a timely manner. I ordered the cover and the foam. I was debating if I should buy the foam. I thought mine was in good shape, but after removing the old cover I was glad I bought the foam seat. Mine was pretty worn out. It took me a couple of hours to complete the job. I did need a friend to help stretch the cover on. The new cover looks great. Now when I open the driver's door I don't have to see that ugly rip and foam showing. Thank you guys at the seat shop for a great product and for the install video.

The parts fit perfect and was easy to install. Thank you for making this so I didn't have to but the whole lid.

The seat cover on my 03 Duramax was in bad shape and scattered with duct tape. I just happened upon the install video and could tell this was a quality product so I ordered one and took it to a local shop for install--took them 20 minutes. Looks fantastic, quality is A+, and matches the Pewter interior perfectly. Very glad I bought this product!

The foam feels like it’s better quality than the oem foam, feels like I’m driving on my memory foam mattress. Super comfortable and was easy to install, I would buy from them again!

2005 Chevy Suburban. DAMN Perfect fit, fast shipping. The only issue I have is now the passenger seat looks really bad. I got the seat cover, new seat foam and seat heater. Only issu I had was the seat heater went in opposite of what I was thinking. Quick online chat and got it taken care of. Thanks Guy's!!! my will loves the new seat bottom!!!

Decent for the "one job and done"....wouldn't do the seat cover replacement without a pair of these but might invest a pair that holds the ring without having to put tension on it and has a bit more cushion on grips. But it'll do the job if you're only doing 1 or 2 seats and not needing this again.

Thank you so very much for including the hog rings for easy installation. Also, this company provided a step by step tutorial video. I would buy from these folks again in a minute. VERY pleased.